Adding a piece of fabric to a pair of jeans is a simple way to give them a whole new look. Even big brother’；s rugged jeans can become stylish hand-me-downs for little sis. Cherie from You and Mie gave her daughter’；s pants a little extra pizzazz by using fabric to turn them into bell bottoms. They are super easy to do and any pair of pre-loved jeans will work.While you are browsing through You and Mie you must also check out her Custom Fabric Photo Book. It would make a great gift for a grandparent. The Boy-cycle Wear she made and put her daughter in has baby hipster written all over it. I want!
Keep reading to check out the groovy Bell Bottoms tutorial…；customized gifts for men
A couple of weeks ago， I made a 60s Flower Child outfit for Project Run &； Play’；s Sewing Through the Decades Sew-Along Challenge. I’；m going to show you how I made regular pants into bell bottoms. It’；s super easy and you can do this for kids or adult pants to add a little extra flare. Get it!？？ Wah waah.This could be fun for a hippie costume or if you just like wide leg pants! Here’；s what you need：
Pants (you’；ll want to use something that is pretty fitted on top， baggy pants won’；t look as good)Fabric for the inset (either a decorative fabric， denim， or something that will match your pants if you want a less noticeable look)The usual sewing necessities (sewing machine， scissorspersonalized gifts for dad， thread， ruler)First， you want to hem up the bottom of your inset fabric. To figure out how much fabric you’；ll need to hem， just decide how wide you want the bottom of your inset to be (my little toddler pants insets were about 4 inches wide) and then double that (because you’；ll need two) and always add a couple inches for good measure. I skipped this step because I left the bottom of my pants unhemmed， but if I had， I would have hemmed about 10 inches of my inset fabric.Then， cut the outside seam of your pants up to the point where you want the pants to start flaring out， usually right below the knee. I just cut as close to the seam as possible on one side， and then cut up the other side of the seam and trim the seam to remove it.Now we’；re going to cut 2 triangles from our inset fabric. The hemmed side will be the bottom of triangle (again， I didn’；t hem， so just pretend ：)). You want your triangle height to be about half an inch taller than the cut you made in your pants’； side seam. I cut about 8 inches up the pant leg， so the height of my triangles are 8.5 inches. As for the width of the bottom –； that’；s up to you. The wider the triangle base， the wider the flare. You decide!!Now it’；s time to sew! Line up one side of the triangle with one cut edge of the pants， right sides together. You want the bottom seams lined up. and sew starting from the bottom with about a 1/4 inch seam allowance (my inset fabric looked the same on both sides， so there was no “；wrong”； side， but make sure your fabric is wrong side facing up).When you open it up， it should look like this on the right side.Now turn your pants inside out and line the other sides up， right sides together. and sew. You want to try and get your seams to meet in the middle at the top of the triangle.When inside out， your pant leg should look something like this.Turn the pants right side out and iron. Repeat with the other pant leg and you’；re done!I hope your little hippie enjoys their pants!!
Check out Cherie’；s many other tutorials such as her， Classic Jumper Tutorial. It’；s so cute that every girl should have one.
Today’s contributor is Jill?from Snugglebug University.? All posts written by Jill?for Make It and Love It can be found HERE.
My husband jokes every time I get the bottle of Mod Podge out that I’m going to Mod Podge fabric to our computer keys or Mod Podge our kids clothing to their bodies. Hey, don’t tempt me. I know, I may go a little overboard with this stuff…….but I just had to try it on some shoes. Originally, I saw the idea on a site my sister showed me. And the lady Mod Podged starburst wrappers to some shoes. It was cute…….but I wanted to try fabric.